Galactic Junk
 
 
 
 

12mm Momentary LED Switch - GJSWM01
with nut
NOT suitable for the Plif Board
Size: 12mm

£4
Colour



12mm Latching Switch - GJLSW01
With Nut

Works with the Plif Board
Size: 12mm

£3


Low Stock
12mm Latching LED Switch - GJLSW02
With Nut
Works with the Plif Board
Size: 12mm

£4
Colour:



12mm Latching switch - Long - GJSW01L
With Nut

Works with the Plif Board
A long version of the latching switch - this will fit in all of the Raxxus switch bodies, but can be a bit "tight" due to the length

Bending/shortening the legs and heatshrink are required for these switches!
Size: 12mm

£3



3x3W RGB LED - GJRGB9W
on a PCB star
includes resistor for the red LED

Click HERE for the RGB LED setup guide
Size: 20mm

£4



3x1W RGB LED - GJLED02
on a PCB star
includes resistor for the red LED

Click HERE for the RGB LED setup guide
Size: 20mm

£3



Optic for RGB LED - GJOPT01
Works with all single LED dies - comes with carrier!


£2



5mm RGB LED - GJ5MMRGB
Common annode LEDs that can be run in parallel with the main blade LEDs to give you a custom coloured crystal chamber or accent light
Size: 5mm

£1



Plif LED Controller - GJPLIF01
*** Just Released! ***

A simple "self build" board kit
(requires basic soldering skills).
Easy build & setup, Flicker
Customisable LED colour, Fade on/off

Click HERE for the Build Guide


£5





Picture
Coming
Soon!
Out of Stock
3400mAh 18650 Battery - GJBAT01
A quality 3400mAh battery that is pre-fitted with a male JST connector


£10



Impact Sensor - GJIMP01
Lost or broken your impact sensor?
Get your replacement here!
Works with most boards that use an external trigger.


£1





Picture
Coming
Soon!

23mm speaker - GJAUD01
These speakers were originally designed for toys and can manage some tough impacts and drops.
While their frequency response isn't as good as some, they are loud and coupled with the right size sound chamber can sound very loud and clear.


£3





Picture
Coming
Soon!

28mm Speaker - GJAUD02


£4



Heatshrink x 10 - GJHS01
Approx 15mm long pre-cut heatshrink tubing.
Works great with switches and recharge ports.


£1



3D Printed Switch Washer - GJ3DSW01
This switch washer conforms properly to the inside of a 1" (25mm) ID sabre. This makes it MUCH easier to tighten the switch nut and prevents it from coming undone during combat!


£2



Recharge port and connector - GJRCP01
A 5.5x2.1mm recharge port (8mm thread)
Supplied with female JST connector and 2 rubber washers


£2



Charity Sticker Pack - GJSTK01
Everyone *LOVES* a sticker!
a random selection of 5 stickers.
50% of all proceeds will be given to charity!

some duplication between packs may occur - but we will try our best!


£1





Picture
Coming
Soon!
Out of Stock
Galactic Junk Internals Kit - GJIKIT01
This kit contains everything to put inside your stunt sabre!

Plif Board Kit
Latching Switch & Switch Washer
LED, Resistor and Optic
Recharge port & Heatshrink
Connectors and Wire
3400mAh 18650 battery

Assembly required!

Pair with one of our hilt kits and you can have a sabre up and running in next to no time!


£25





Picture
Coming
Soon!
Out of Stock
Galactic Junk Internals Kit (no battery) - GJIKIT02
This kit contains nearly everything you need to put inside your stunt sabre!

Plif Board Kit
Latching Switch & Switch Washer
LED, Resistor and Optic
Recharge port & Heatshrink
Connectors and Wire

Assembly required!

Pair with one of our hilt kits and you can have a sabre up and running in next to no time!


£15


© 2018 - Galactic Junk